Standard Gain Horn Antenna SAS-588

  • Standard Gain Horn Antenna


This Standard Gain Horn Antenna will provide reliable, repeatable measurements. An ideal solution and a standard workhorse of any EMC test house for compliance testing.


  • 26.5 GHz to 40 GHz
  • Individually Calibrated at 1 Meter Horizontal Polarity
  • FCC, MIL-STD, VDE and TEMPEST Testing
  • Rugged Construction
  • Three Year Warranty

CAGE Code: 54656
Schedule B: 8529.10.9000

Product Details

The Standard Gain Horn Antennas are designed specifically for utilization in emissions and immunity testing over the frequency range of 1 to 40 GHz. Each antenna is linearly polarized and has medium gain, low VSWR, and a constant antenna factor. The Standard Gain Horn performance is very precise and predictable through design parameters. Comparisons of measured versus computed antenna factors and gain have been shown to be +/- .5 dB. Therefore, the antenna is considered to be a standard reference, similar to that of a resonant dipole below 1 GHz. The coax-to-waveguide adapter is the only power-limiting component on the antenna and can be removed if high fields are desired. Each Standard Gain Horn comes with a tripod mount that adapts to any tripod with 1/4-20 male threads. Horizontal and vertical polarization is obtained by rotating the antenna on the tripod.

Included parts:
  • SAS-588 Antenna with attached waveguide to coax adapter and tripod mount
  • Antenna Calibration Manual

Antenna Specifications

SAS-588 Standard Gain Horn Antenna
Frequency Range: 26.5 GHz - 40 GHz
Antenna Factor: 46.0 dB/m
Gain: 14.6 dBi
Maximum Continuous Power: 10 Watts
Max Radiated Field: 100 V/m
Impedance: 50 ohm
VSWR: 1.3:1 (1.5:1 max)
Connector: WR-28 to 2.9mm female adapter
Mounting Base: 1/4 - 20 Thread, female
Physical Dimensions:
Length: 2.9 in.   (7.37 cm)
Width: 0.6 in.   (1.52 cm)
Height: 0.9 in.   (2.29 cm)
Weight: 0.1 lbs (0.05 kg)

Typical Antenna Data

SAS-588 Standard Gain Horn Antenna

Additional Resources

SAS-588 Standard Gain Horn Antenna

Product Datasheet

Operation Manual

Typical conversion formulas

Antenna Beamwidth Coverage Calculations

Shipping Information:
Carton size: 13" x 10" x 5"
Shipping Weight: 2 lbs.
* These are approximate dimensions and will vary depending on other items ordered.

Recommended Accessories

SAS-588 Standard Gain Horn Antenna
Plastic Tripod

ATU-514 - Plastic Tripod

The ATU-514 is a collapsible tripod is built with all non-metallic materials that will not influence your antenna measurements.


Az and El Head

AEH-510 - Az and El Head

The AEH-510 Azimuth and Elevation head is used to assist the test engineer in pointing the mounted test antenna towards the device under test. This adjustable antenna mount has a rugged 4" mounting surface with a Captive 1/4-20 male thread for mounting all of A.H. Systems and most other compliance measurement antennas.


1.5 Meter Low-Loss Cable

SAC-40G-1.5 - 1.5 Meter Low-Loss Cable

AH Systems assembles high performance microwave cable that utilizes only the very best materials. With plenty of raw stock on hand, we can create a custom length high precision cable assembly within a few days. The outer jacket is a tough, high temperature thermoplastic that can withstand temperatures from -65 to +200 Celsius. All this adds up to a very superior microwave cable product that can meet the most demanding requirements